SKU:

OPUS BT-C3100 Smart Smart Digital Intelligent 4-Slot Battery Charger(UK Plug)
OPUS BT-C3100 智能4槽电池充电器（英规）
条码：6922889532196
HSCode：85069090
批量修改原始型号 		采购：Nicole  编辑：Shadow  产品经理：Maura


1. Four independent charging channels: With independent charging control chip, precise control of the charging situation of each charging slot, the working power of the charger is 12V-3A, and a dedicated DC switching power supply is used
2. There are four levels of charging current available for selection, 200/300/500/700/1000mA, among which, if there is only 1, 4 channels with batteries, the current levels are: 200/300/500/700/1000 / 1500/2000mA, the discharge battery can be set to 200/300/500/700/1000mA
3. The discharging mode does not switch to charging, and the battery discharge capacity is displayed. In charging mode, the 4.21V charger is judged to be fully charged
4. LCD screen: Can display the real-time charge/discharge capacity, voltage, current, and time of the 4 channels of batteries
5. Four working modes: Charge, discharge, repair and capacity test and battery internal resistance test
6. Applicable battery type: Lithium battery, model: 10440, 14500, 16340, 18500, 18650, 26650, 26500; Ni-MH battery, model: AA, AAA, C, D
7. Working temperature: 0 to 40 degrees celsius
8. Note: The product does not contain batteries

Function button:
1. MODE operating mode selection button
2. DISPLAY display mode button
3. CURRENT current adjustment button
4. SLOT, can individually adjust the working mode of each channel

The specific operation method of the charger:
1. Long press MODE for 2 seconds to enter the working mode to select, and then press this key to have four working modes to choose from, namely charge, discharge, repair capacity test and battery internal resistance test
2. Press DISPLAY to display the charge current, battery voltage, battery power, and battery charge and discharge time respectively.
3. When power on, the charger defaults to the charging mode and the charging current is 500mA
4. When powering on, press CURRENT to adjust the current. When entering work, if you want to adjust the current again, you need to switch the working mode to press this key to be effective. The charge and discharge current can be adjusted.
5. Press SLOT to adjust the working mode of each channel individually
6. When the temperature of the battery exceeds 40 degrees when the battery is charged or the temperature of the PCB board exceeds 40 degrees, the fan will start to rotate.
7. Select the capacity test working mode, the current can be the same as charging

1. 四个独立充电通道：拥有独立充电控制芯片，准确控制每一个充电槽的充电情况，充电器工作电源为12V-3A，使用专用DC开关电源
2. 可供选择充电电流共有四档200 / 300 / 500 / 700 / 1000mA, 其中如果只有1，4通道有电池的时候可选择电流的档位分别为：200 / 300 / 500 / 700 / 1000 / 1500 / 2000mA，放电电池可以设置大小有200 / 300 / 500 / 700 / 1000mA
3. 放电模式不转充，显示电池放电容量。充电模式下，到4.21V充电器判定为充满
4. 液晶屏：可显示4个通道电池的实时充电/放电容量、电压、电流、时间
5. 四种工作模式：充电，放电，修复和容量测试和电池内阻测试
6. 适用电池类型：锂电池，型号：10440，14500，16340，18500，18650，26650，26500；镍氢电池，型号：AA，AAA，C，D
7. 工作温度：0到 40摄氏度
8. 注意：产品不包含电池

功能按键：
1.MODE工作模式的选择按键
2.DISPLAY显示模式按键
3.CURRENT电流大小的调整按键
4.SLOT，可单独调节各个通道的工作模式

充电器具体操作方法：
1. 长按MODE 2秒钟，进入工作模式进行选择，再按此键有四种工作模式可供选择,分别是充电、放电、修复容量测试和电池内阻测试
2. 按DISPLAY可分别显示充电电流大小，显示电池电压值，电池电量，电池充放电的时间
3.上电时充电器默认充电模式且充电电流大小为500mA
4.上电时，按CURRENT，可调节电流大小，当进入工作时，要再次调节电流需切换工作模式时按此键才有效，可调整充电与放电电流的大小
5. 按SLOT，可单独调节各个通道的工作模式
6. 当电池充电时温度超过40度时或者PCB板温度超过40度启动风扇转动。
7. 选择容量测试工作模式，可选择电流大小与充电一样
代码：

Specification:
Package weight
One package Weight 0.7kgs / 1.54lb
One Package Size 22.0cm * 16.0cm * 8.0cm / 8.66inch * 6.3inch * 3.15inch
Qty per Carton 20
Carton Weight 15kgs / 33.07lb
Carton Size 45cm * 33cm * 42cm / 17.72inch * 12.99inch * 16.54inch

代码：