SKU:

SINOTIMER SDM007 Din Rail AC Voltage Current Totalized Time Frequency Digital Display Meter
SINOTIMER SDM007 导轨式交流电压电流累计时间频率数显表
条码：6922975292541
HSCode：90303390
批量修改原始型号 		采购：Kitty  编辑：Randi  产品经理：Maura


Parameters:
1. Measurement accuracy: 1+/-2 percent of the word
2. Display: 0.32-inch LED digital tube, voltage with 4-bit red LED display, current with 4-bit green LED display, timing, frequency with 5-bit red LED display
3. Measuring range:
- Voltage: AC80-300V
- Current: AC0-100.0A
- Frequency: 45-65Hz
- Cumulative timing: 1m-99999h
4. Measuring speed: about 2 times/s
5. Installation: din-rail type directly mounted on the same rail as the air switch
6. Dimensions: 54 x 80 x 64mm

Usage and wiring method:
1. Connect the measured voltage to terminals 1 and 2 at the lower left of the meter
2. Built-in transformer according to figure 1 wiring diagram wiring, the measurement circuit of the wire through the instrument lower hole, the wire into the direction of the user according to the use of any choice, you can be from the instrument lower hole into the upper out, or from the instrument upper holes into the lower out, into the direction of the different will not affect the results of the measurement
3. After connecting the wires according to the wiring diagram, put on the measuring voltage, the meter will start to display normally, the meter will display the measured voltage, current and frequency, press the button (SAM CK) on the left side of the meter panel, the frequency display on the meter will be converted to the cumulative timing display, and press the button (SAMCK) again, the cumulative timing display will be converted to the frequency display
4. Accumulated timing back to zero operation: press the left button (SAM CK) on the instrument panel, so that the frequency display is converted to display the cumulative timing condition, and then press and hold the button (SAM CK) for 5 seconds, the cumulative timing will automatically be 1 all displayed to zero

Note: this meter is only suitable for pure AC 45-65Hz mains power supply, it can not be used for square wave, inverter output, corrected sine wave and other circuits on the measurement, otherwise the meter will be damaged

参数：
1. 测量精度：百分之1+/-2个字
2. 显示器：0.32英寸LED数码管，电压采用4位红色LED显示，电流用4位绿色LED显示，计时、频率采用5位红色LED显示
3. 测量范围：
- 电压：AC80-300V
- 电流：AC0-100.0A
- 频率：45-65Hz
- 累积计时：1m-99999h
4. 测量速度：约2次/s
5. 安装方式：导轨式直接安装在与空气开关相同 的导轨上面
6. 尺寸：54 x 80 x 64mm

使用和接线方法：
1. 将被测量的电压接入仪表的左下方的1和2接线端子上
2. 内置互感器按图一接线图接线，将测量回路的导线穿过仪表的下方的圆孔，导线的穿入方向用户根据使用的情况任意选择，可以从仪表的下面圆孔穿入上面出来，或从仪表上面圆孔穿入下面出来，穿入方向不一样不会影响测量结果
3. 仪表按接线图接好线后，通上测量电压,仪表开始正常显示，仪表显示测量的电压、电流、频率。按一下仪表面板上左面的按钮(SAMCK)，仪表上的频率显示转换成累积计时的显示，再按一次按钮(SAMCK)，累积计时显示转换成频率显示
4. 累积计时回零的操作：按一下仪表面板上左面的按钮(SAM CK)，使频率显示转换到显示累积计时状况，然后按住按钮(SAM CK)5秒钟，累积计时自动会1全部显示为零

注意：本仪表只适用于纯交流45-65Hz的市电电源，不能用于方波、逆变器输出、修正的正弦波等电路上测量，否则会使仪表损坏
代码：

Specification:
Package weight
One package Weight 0.14kgs / 0.31lb
One Package Size 9.0cm * 6.0cm * 7.0cm / 3.54inch * 2.36inch * 2.76inch
Qty per Carton 140
Carton Weight 20.7kgs / 45.64lb
Carton Size 51cm * 38cm * 32cm / 20.08inch * 14.96inch * 12.6inch

代码：