SKU:

12V/24V 4 Pin 5 Pin Automotive Relay Tester(CNBJ-722)
12V/24V 4 Pin 5 Pin 汽车继电器检测仪（CNBJ-722）
条码：6922918397013
HSCode：90308200
批量修改原始型号 		采购：Felix  编辑：Leah  产品经理：caifeng


1. Material: ABS
2. Application range: 12V/24V automotive relay
3. LED high-definition display, can be operated in dim environment
4. Lighting design, no fear of the night, more convenient to detect automotive relays, just one button to turn on
5. This product is mainly used to detect whether the automotive relay is normal
6. Size: 97x27x200mm
7. Note: The product requires 18650 batteries x2, and the battery is not shipped!

Instructions:
1. Install 2 batteries into the instrument (according to the instructions), and do not invert the positive (+) and negative (x) poles of the batteries
2. "OFF / 12V / 24V" is the 12V relay and 24V relay selection key; after the power button is turned on, the current battery power will be displayed immediately (if the battery power is insufficient, please charge it in time); and there is a 12V/24V relay selection; select the voltage volts of the corresponding automotive relay to test
3. "4 PIN / 5 PIN" is the four-pin and five-pin key; select the four-pin and five-pin under the automotive relay to be tested (usually these two pins), if there are special pins, it cannot be tested
4. "TEST" is the test key; select the corresponding relay type (12V or 24V), pin (4 PIN or 5 PIN), when the test button is pressed, the instrument will open and close 10 times for detection, and end when a buzzer sound is heard; and the display area will show "OK" or "BAD", which means "OK" means the relay being tested is good; "BAD" means the relay being tested is bad (analyzed based on the length of time it takes to be released)
6. After using the instrument, pull the switch to "OFF" to turn off the power, remove the relay



1. 材质：ABS
2. 应用范围：12V/24V汽车继电器
3. LED高清显示屏，昏暗环境也能操作
4. 照明灯设计，不惧黑夜， 检测汽车继电器更方便一键开启即可
5. 本产品主要是检测汽车继电器是否正常
6. 尺寸：97x27x200mm
7. 注意：产品使用需要18650电池x2，出货不带电池！

使用说明书:
1. 将2节电池装入仪器(按指示相对应)，正极(+)、负极(x)切勿倒置电池
2. “OFF / 12V/ 24V”是12V继电器和24V继电器选择键；电源键开机后，会显示当前电池电量(如电池电量不足请及时充电)；并有12V/24V继电器选择；选择相对应汽车继电器的电压伏数来测试
3. “4 PIN / 5 PIN”是四脚和五脚键；选择被检测汽车继电器下面四脚和五脚(通常都是这两种脚位)，如有特殊脚位，则不可以测试
4. “TEST”是测试键；选择好相对应继电器类型(12V或24V)、脚位(4 PIN或5 PIN)后，当按下测试键，仪器会开启闭合10次检测动作，当听到蜂鸣声后结束；并显示区会显示“OK”或“BAD”；分别代表“OK”说明被检测继电器是好的；“BAD”说明被检测继电器是坏的(根据释放的时间长短来分析)
6. 使用完仪器后，开关拔到“OFF”关闭电源，移开继电器


代码：

Specification:
Package weight
One package Weight 0.49kgs / 1.08lb
One Package Size 26.0cm * 24.0cm * 5.0cm / 10.24inch * 9.45inch * 1.97inch
Qty per Carton 6
Carton Weight 4.1kgs / 9.04lb
Carton Size 28cm * 26cm * 32cm / 11.02inch * 10.24inch * 12.6inch

代码：