SKU:

Dual M.2 NVME SSD RAID Array Mobile Hard Drive Enclosure Type-C USB3.2 GEN2x2 20G 586R(Dark Gray)
M.2 NVME SSD RAID阵列移动硬盘盒Type-C USB3.2 GEN2x2 20G 586R（深空灰）
条码：6922594209718
HSCode：84733010
批量修改原始型号 		采购：Nicole  编辑：Jessica  产品经理：Maura


1. Support capacity: 4TB
2. Transfer interface: USB2.0, USB3.0, USB3.1, USB3.2, USB4
3. Transmission speed: 20Gbps
4. Master control: JMS586R
5. Power interface: Type-C
6. Suitable for multiple SSD specifications: M.2 NVME 2230 2242 2260 2280
7. P1/P2 SSD indicator: green light on when SSD recognition is normal, green light blinks when reading and writing data, red light blinks when SSD is faulty
8. Size: about 10.6 x 5.7 x 1.7cm
9. Weight: about 168.8g

Features:
1. Mobile storage, convenient, Type-C data interface, compatible with computers, tablets, cell phones
2. Quiet cooling fan, accelerate the hard disk cooling, make the operation more stable
3. Misdialing, mistakenly touching RAID mode and RESET will not change the array, press and hold the RESET button and then turn on the power to change the array
4. RAID1 mode switch to PM mode, split into two independent disks, one of the disks in the offline state, enter the disk manager to offline disk online, RAID1 mode data still exists in the two disks
5. 5 minutes, no data read and write, the device enters the automatic sleep state, reduce power consumption, protect the life of the hard disk
6. Replacement of SSD specifications can be installed directly, without opening the board, convenient and fast

RAID mode setup steps:
1. Install the SSD, plug in the data and power cables, and then turn off the power
2. Set the RAID mode to the desired position
3. Press and hold the reset button, then turn on the power switch and release the reset button after 3s of beeping
4. After the RAID setup is complete, you need to enter disk manager for initialization
5. Note: data will be lost when switching RAID modes, so please be careful
6. Suggestion: backup your data before switching RAID mode

Installation steps:
1. Open the bottom cover
2. Insert the SSD into the M.2 NVME connector at an angle of 45 degrees
3. Attach the removable studs to the end of the SSD.
4. Use a screwdriver to lock the studs onto the board
5. Close the bottom cover and lock the screws.

Packing list:
- HDD case x 1
- Type-C cable x 1
- Screwdriver x 1
- Moving studs x 2
- Housing screws x 2

1. 支持容量：4TB
2. 传输接口：USB2.0, USB3.0, USB3.1, USB3.2, USB4
3. 传输速度：20Gbps
4. 主控制：JMS586R
5. 电源接口：Type-C
6. 适用于多种规格SSD：M.2 NVME 2230 2242 2260 2280
7. P1/P2 SSD指示灯：当SSD识别正常时，绿灯亮起，读取和写入数据时绿灯闪烁，SSD出现故障时红灯会闪烁
8. 尺寸：约10.6 x 5.7 x 1.7cm
9. 重量：约168.8g

特点：
1. 移动存储，方便快捷，Type-C数据接口，兼容电脑、平板、手机
2. 静冷风扇，加速硬盘降温，让运行更稳定
3. 误拨、误触RAID模式和RESET不会改变阵列、按住RESET键不松再打开电源才会改变阵列
4. RAID1模式切换到PM模式，拆分成2个独立磁盘，其中一个盘处于脱机状态，进入磁盘管理器将脱机磁盘联机，RAID1模式下的资料仍然存在于2个磁盘内
5. 5分钟之内，没有进行数据读写，设备进入自动休眠状态，降低功耗，保护硬盘使用寿命
6. 更换SSD规格可直接安装，无需打开板子，方便快捷

RAID 模式设置步骤：
1. 安装固态硬盘，插入数据线和电源线，然后关闭电源
2. 将 RAID 模式档位拨至所需位置
3. 按住重置按钮，然后打开电源开关，在听到滴声3秒钟后松开重置键
4. RAID 设置完成后，需要进入磁盘管理器进行初始化
5. 注意：切换RAID模式，数据将丢失，请谨慎操作
6. 建议：切换RAID模式之前，将数据备份

安装步骤：
1. 打开底盖
2. 将SSD 45度斜插入M.2 NVME接口
3. 将移动螺柱卡到SSD尾部
4. 使用螺丝刀将螺柱锁到电路板上
5. 盖上底盖，将螺丝锁上

包装内容:
- 硬盘盒 x 1
- Type-C线 x 1
- 螺丝刀 x 1
- 移动螺柱 x 2
- 外壳螺丝 x 2
代码：

Specification:
Package weight
One package Weight 0.2kgs / 0.44lb
One Package Size 17.0cm * 12.0cm * 5.0cm / 6.69inch * 4.72inch * 1.97inch
Qty per Carton 100
Carton Weight 21kgs / 46.3lb
Carton Size 50cm * 34cm * 32cm / 19.69inch * 13.39inch * 12.6inch

代码：