Overview 1. XCore407I is an STM32 MCU core board that features the STM32F407IGT6 on board. 2. Clock circuit, USB power management 3. Onboard devices: USB HS PHY, Ethernet PHY, 1G Bit NandFlash 4. Connectors:USB HS (mini / type A), USB FS (mini), Ethernet (RJ45) 5. All the idle I/O ports are accessible on the pin headers 6. 2.0mm pin header pitch, smaller size, easier to integrate into user system 7. Note : please consider the EVK407I, which supports easily programing/debugging.
What is On Board STM32F407IGT6 development board on board resource
1. STM32F407IGT6: The high performance STM32 MCU which features: - Core: Cortex-M4 32-bit RISC - Feature: a full set of single-cycle DSP instructions - Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz - Operating Voltage: 1.8V-3.6V - Package: LQFP176 - Memories: 1024kB Flash, 192+4kB SRAM - MCU communication Interfaces: -- 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C -- 1 x FSMC, 1 x SDIO, 2 x CAN -- 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY -- 1 x 10/100 Ethernet MAC -- 1 x 8 to 14-bit parallel camera interface - AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit) - Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP 2. MIC2075-2, onboard USB FS power management device 3. AMS1117-3.3, 3.3V voltage regulator 4. K9F1G08U0E, 1G Bit NandFlash 5. DP83848, Ethernet PHY 6. MIC2075-1, onboard USB HS power management device 7. USB3300, USB HS PHY 8. Power supply switch, powered from 5Vin or USB connection 9. Boot mode switch, for configuring BOOT0 pin 10. Power indicator 11. USB FS LED 12. USB HS LED 13. Reset button 14. 8M crystal, MCU clock, enables the MCU run at higher speed by frequency multiplication 15. 24M crystal, USB3300 clock 16. 50M crystal, DP83848 clock 17. 32.768K crystal, for internal RTC with calibration 18. Ethernet connector 19. USB FS mini connector 20. USB HS mini connector 21. USB HS type A connector 22. MCU pins expander, VCC, GND and all the idle I/O ports are accessible on expansion connectors for further expansion 23. USB OTG/HOST jumper 24. VREF/VBAT jumper 25. Ethernet I/O selection solder joint 26. USB HS I/O selection solder joint 27. PDR selection solder joint: 1.8-3.6V, -40~105℃ OR 1.7-3.6V, 0~70℃
Package Contents 1. XCore407I development board x 1 2. USB type A to Mini-B cable x 1 3. Software CD x 1 概观 1. XCore407I是STM32 MCU核心板,板载STM32F407IGT6。 2. 时钟电路,USB电源管理 3. 板载设备:USB HS PHY,以太网PHY,1G Bit NandFlash 4. 连接器:USB HS(迷你/ A型),USB FS(迷你),以太网(RJ45) 5. 所有空闲I / O端口均可通过引脚头访问 6. 2.0mm引脚头间距,更小的尺寸,更易于集成到用户系统中 7. 注意:请考虑EVK407I,它支持轻松编程/调试。
板上有什么 STM32F407IGT6开发板上的资源
1. STM32F407IGT6:高性能STM32 MCU,具有以下特点: - 核心:Cortex-M4 32位RISC - 功能:全套单周期DSP指令 - 工作频率:168MHz,210 DMIPS / 1.25 DMIPS / MHz - 工作电压:1.8V-3.6V - 包装:LQFP176 - 存储器:1024kB闪存,192 + 4kB SRAM - MCU通信接口: - 3 x SPI,4 x USART,2 x UART,2 x I2S,3 x I2C - 1个FSMC,1个SDIO,2个CAN - 1个USB 2.0高速/全速设备/主机/ OTG控制器,带有专用DMA,ULPI和片上全速PHY - 1 x 10/100以太网MAC - 1 x 8至14位并行相机接口 - AD和DA转换器:3 x AD(12位,1μs,共享24个通道); 2 x DA(12位) - 调试/编程:支持JTAG / SWD(串行线调试)接口,支持IAP 2. MIC2075-2,板载USB FS电源管理器 3. AMS1117-3.3,3.3V稳压器 4. K9F1G08U0E,1G Bit NandFlash 5. DP83848,以太网PHY 6. MIC2075-1,板载USB HS电源管理器件 7. USB3300,USB HS PHY 8. 电源开关,由5Vin或USB连接供电 9. 引导模式开关,用于配置BOOT0引脚 10. 电源指示灯 11. USB FS LED 12. USB HS LED 13. 重置按钮 14. 8M晶振,MCU时钟,通过倍频使MCU以更高的速度运行 15. 24M晶振,USB3300时钟 16. 50M晶振,DP83848时钟 17. 32.768K晶振,用于带校准的内部RTC 18. 以太网连接器 19. USB FS迷你连接器 20. USB HS迷你连接器 21. USB HS A型连接器 22. MCU引脚扩展器,VCC,GND和所有空闲I / O端口均可通过扩展连接器访问,以便进一步扩展 23. USB OTG / HOST跳线 24. VREF / VBAT跳线 25. 以太网I / O选择焊点 26. USB HS I / O选择焊点 27. PDR选择焊点:1.8-3.6V,-40~105℃或1.7-3.6V,0~70℃
包装内容 1. XCore407I开发板x 1 2. USB A型到Mini-B电缆x 1 3. 软件CD x 1
代码: