Overview 1. Core405R is an STM32 MCU core board designed for STM32F405RGT6, supports further expansion. It is ideal for starting application development with STM32F family. 2. Minimal ready-to-run system, integrates clock circuit, USB control circuit, USB connector, 3. etc. 3. All the I/O ports are accessible on the pin headers 4. JTAG/SWD programming/debugging interface 5. 2.54mm header pitch, allowed to be plugged-in your application board
What has On Board 1. STM32F405RGT6: The high performance STM32 MCU which features: - Core: Cortex-M4 32-bit RISC - Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz - Operating Voltage: 1.8V-3.6V - Package: LQFP64 - Memories: 1MB Flash, 192+4kB SRAM - MCU communication Interfaces: -- 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C, 1 x SDIO, 2 x CAN --1 x USB 2.0 HS/FS device/host/OTG controller with dedicated DMA, on-chip full-speed PHY --1 x USB HS ULPI (external PHY required) - AD & DA converters: 3 x AD (12-bit, 1μs, shares 16 channels); 2 x DA (12-bit) - Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP 2. AMS1117-3.3: 3.3V voltage regulator 3. MIC2075-2: onboard USB power management device 4. Power supply switch, powered from 5Vin or USB connection 5. Boot mode selection, for configuring BOOT0 pin 6. Power indicator 7. VBUS LED 8. Reset button 9. 8M crystal 10. 32.768K crystal, for internal RTC with calibration 11. JTAG/SWD interface: for debugging/programming 12. USB connector, used for establishing USB communication between PC and the STM32 development board 13. MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion 14. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG 15. USB jumper - Short the jumper when using USB - Open the jumper to disconnect from related I/O port 16. VBAT selection jumper - Short the jumper to use system power supply - Open the jumper to connect the VBAT to external power, such as battery
Package Contents 1. Core405R x 1 2. USB type A to Mini-B cable x 1 3. Software CD x 1 概观 1. Core405R是专为STM32F405RGT6设计的STM32 MCU核心板,支持进一步扩展。它是使用STM32F系列开始应用程序开发的理想选择。 2. 最小的即用型系统,集成了时钟电路,USB控制电路,USB连接器等。 3. 引脚头上可以访问所有I / O端口 4. JTAG / SWD编程/调试接口 5. 2.54mm插头间距,允许插入您的应用板
板上有什么 1. STM32F405RGT6:高性能STM32 MCU,具有: - 核心:Cortex-M4 32位RISC - 工作频率:168MHz,210 DMIPS / 1.25 DMIPS / MHz - 工作电压:1.8V-3.6V - 套餐:LQFP64 - 存储器:1MB闪存,192 + 4kB SRAM - MCU通信接口: - 3 x SPI,4 x USART,2 x UART,2 x I2S,3 x I2C,1 x SDIO,2 x CAN - 1个USB 2.0 HS / FS设备/主机/ OTG控制器,带有专用DMA,片上全速PHY --1 x USB HS ULPI(需要外部PHY) - AD和DA转换器:3 x AD(12位,1μs,共享16个通道); 2 x DA(12位) - 调试/编程:支持JTAG / SWD(串行线调试)接口,支持IAP 2. AMS1117-3.3:3.3V稳压器 3. MIC2075-2:板载USB电源管理设备 4. 电源开关,由5Vin或USB连接供电 5. 引导模式选择,用于配置BOOT0引脚 6. 电源指示灯 7. VBUS LED 8. 重置按钮 9. 8M水晶 10. 32.768K晶振,用于带校准的内部RTC 11. JTAG / SWD接口:用于调试/编程 12. USB连接器,用于在PC和STM32开发板之间建立USB通信 13. 可通过扩展连接器访问MCU引脚扩展器,VCC,GND和所有I / O引脚,以便进一步扩展 14. 5Vin pinheader,使用USB HOST / OTG时需要5V电源 15. USB跳线 - 使用USB时短接跳线 - 打开跳线以断开与相关I / O端口的连接 16. VBAT选择跳线 - 短接跳线以使用系统电源 - 打开跳线,将VBAT连接到外部电源,如电池
包装内容 1. Core405R x 1 2. USB A型到Mini-B电缆x 1 3. 软件CD x 1
代码: