Description: 1.Brand new and high quality. 2. Low-noise receive gain. 3. Signal activity LED indicates 4. High Gain, High Value, High Performance. 5. Maximum output power of 8000mW by the Booster. 6. Plug-and-play, Easy installation, no driver needed. 7. Ideal for increase the 2400-2500 MHz frequency devices. 8. Increase the effective range and coverage area of your Wi-Fi network. 9. Simply attach the booster in between the standard antenna on a wireless router or wireless access point and watch your range grow. 10. The amplified wireless signal may even penetrate complex environments with many walls and obstacles. 11. Ideal for use with 2.4GHz Wireless LANs, Support 802.11b, 802.11g, 802.11n (2.4Ghz mode only). Features: 1. Operation Range: 2400-2500 MHz. 2. Operation Mode: Bi-directional, half-duplex, Auto-Switching via carrier sensing. 3. Frequency Response: ± 1dB over operation range. 4. Input Power: 3dBm (Min.)-20dBm (Max.). 5. Input Power 5-20 dBm. Supoort Standard: IEEE 802.11b/g/n Frequency: 2400-2500Mhz Working Pattern: TDD RF Output Power: 39dBm(8W) Input Trigger Power: Min:3dBm, Max: 20dBm Transmit Gain: 17dB typical Receiver Gain: 11dB typical Switch Time Delay:>1us Noise Figure: 30dB(typical) Working Voltage: 6-18VDC,12V/2A *Distance: 3-5KM Using Precautions 1.Recommend the input power of RFIN port to between 7dBm and 13dBm. 2.Make sure all power supply to the booster and the AP/Router unit be disconnected before removing or changing antenna. 3.When finishing connecting the booster and the AP/Router, restore power supply first to the booster and then to AP/Router subsequently. 4Waterproof, lightning protection equipment should be attached to outdoor antenna. 5. Keep away from heat and keep ventilated. 6. Please comply with local regulations of electromagnetic radiation.
描述: 1.全新高品质。 2. 低噪声接收增益。 3. 信号活动指示灯指示 4.高增益,高价值,高性能。 5.升压器最大输出功率为8000mW。 6.即插即用,安装方便,无需驱动程序。 7.非常适合增加2400-2500 MHz频率的设备。 8. 增加 Wi-Fi 网络的有效范围和覆盖区域。 9. 只需将放大器连接到无线路由器或无线接入点的标准天线之间,即可观察您的范围增长。 10. 放大的无线信号甚至可以穿透具有许多墙壁和障碍物的复杂环境。 11. 非常适合与 2.4GHz 无线局域网配合使用,支持 802.11b、802.11g、802.11n(仅限 2.4Ghz 模式)。 特征: 1.工作范围:2400-2500 MHz。 2.操作模式:双向,半双工,通过载波感应自动切换。 3. 频率响应:在工作范围内± 1dB。 4.输入功率:3dBm(最小)-20dBm(最大)。 5. 输入功率 5-20 dBm。 标准:IEEE 802.11b/g/n 频率:2400-2500兆赫 工作模式:TDD 射频输出功率:39dBm(8W) 输入触发功率:最小:3dBm,最大:20dBm 发射增益:17dB(典型值) 接收器增益:11dB(典型值) 开关延时:>1us 噪声系数:30dB(典型值) 工作电压:6-18VDC,12V / 2A 距离:3-5公里 使用注意事项 1.建议RFIN端口的输入功率在7dBm和13dBm之间。 2.在拆卸或更换天线之前,请确保断开升压器和AP/路由器单元的所有电源。 3.连接完升压器和接入点/路由器后,首先恢复升压器的电源,然后恢复接入点/路由器的电源。 4.防水、防雷设备应安装在室外天线上。 5.远离热源,保持通风。 6.请遵守当地电磁辐射法规。
提交