null 查看产品详细信息 产品型号: 侵权图库
提醒 2:该产品涉及专利问题,不能在Alibaba上发布!
型号:EDA0030725     大类别:In Car     第2级类别:Repair Tools  -->子类别:Sheet Metal Tools   审核产品   所有审核和提问(new)  链接英文名称:36 in 1 12V Car Cigarette Lighter Plug Paintless Dent Puller
中文名称:36件套 12V车载点烟器插头汽车凹陷无痕修复工具
颜色:
包装:Plastic Bag
配件:null
装箱资料:
每箱:14pcs
重量:23.55kgs
外箱尺寸:52cm * 48cm * 42cm
采购:Felix  编辑:Ellie(2022-06-06)  美工:Ellie
           
1. 20 PCS of dent & ding puller tab, replacement suckers in different shapes for multiple purposes.
2. Repairs the dents on your car.
3. Slide hammer is more powerful for paintless dent repair, conquer big dent.
4. Use widely for the sheet metal processing of automobile, refrigerator, motorcycle, washing machine, etc.
5. Steps:
(1). Clean the dent with a clean wet cloth
(2). Mount the glue stick into the glue gun, pull the trigger to let the glue stick enter into the glue gun, connect the power source and preheat for 5 minutes
(3). Use a proper drawing gasket. Large dent requires a large drawing gasket. (Note: The larger the drawing gasket is, the larger the drawing force is)
(4). Pull the trigger and apply the drawing gasket with extruded glue (The 4 holes of gasket should be applied with hot melt glue)
(5). Fast place the drawing gasket with hot melt glue at the center of dent, press lightly until the glue cures and adheres (Let the glue cool for about 8 minutes. The cooling time should be less than 10 minutes and should be shorter slightly in winter)
(6). Align the T-shaped repairer and press the drawing gasket with hot melt glue, pull the sliding rod backwards to pull up the dent
(7). Check with a Line board. If dent still exists, knock it slightly with a flattening hammer or pen
(8). Clean the repaired place with a clean wet cloth
6. Package:
2 in 1 puller x 1
12V 20W Glue Gun x 1, cable length: 5m
Blue Tabs x 10
Red Tabs x 10
Black Glue Sticks x 5
Yellow Glue Sticks x 5
Shovels x 2
Towel x 1
Alcohol Bottle(Alcohol not included) x 1
English Manua




中文描述:
1. 20 件凹痕拉环,可更换不同形状的吸盘,用于多种用途。
2. 修复汽车上的凹痕。
3. 滑动锤无漆凹痕修复更强大,征服大凹痕。
4. 广泛用于汽车、冰箱、摩托车、洗衣机等的钣金加工。
5. 步骤:
(1). 用干净的湿布清洁凹痕
(2). 将胶棒装入胶枪,扣动扳机让胶棒进入胶枪,接通电源预热5分钟
(3). 使用适当的拉丝垫片。大凹痕需要大的拉丝垫片。 (注:拉伸垫片越大,拉伸力越大)
(4). 扣动扳机,用挤出胶涂抹拉丝垫片(垫片的4个孔应涂上热熔胶)
(5). 将涂有热熔胶的拉丝垫片快速放置在凹痕中心,轻轻按压直至胶水固化并粘附(让胶水冷却约8分钟。冷却时间应小于10分钟,冬季应稍短)
(6). 对准T型修整器,用热熔胶压紧拉丝垫片,向后拉动滑杆拉起凹痕
(7). 用线路板检查。如果凹痕仍然存在,用压扁的锤子或钢笔轻轻敲一下
(8). 用干净的湿布清洁修理处
6. 包装:
2 合 1 拉拔器 x 1
12V 20W胶枪 x 1,线长:5m
蓝色标签 x 10
红色标签 x 10
黑色胶棒 x 5
黄色胶棒 x 5
铲子 x 2
毛巾 x 1
酒精瓶(不含酒精)x 1
英文说明书 x 1
工具包 x 1



搜索关键词:Hail Removal, Dent Repair Tool, Dent Puller, Car Dent Remover Repair Kit, Car Damage Fix

OEM/ODM are Welcome! we can make Customize design and print your logo